疑似ares自定义建造格子bug导致ai建造不受限制

SovietAntiInfan

如题，用ares给自己新增的建筑自定义了个十字形的建造范围，同时也精简了一些原版建筑占地面积，无意间发现电脑造了很多船厂（船厂被我精简成了类十字形），本来没留意，后来发现新增的那个建筑电脑好像卡住一样不停造，不停放置，可我明明写了buildlimit=1，查阅词典发现电脑无视这一属性，而且除发电厂矿场外其他默认都只建一个，又尝试修改BuildCat等属性都不行，后来联想到电脑多造的船厂而我也刚好精简过其占地面积，就把占地面积改成了传统nxn的形式，问题就消失了。也许是因为形状过于奇怪，也许是因为过度精简导致“穿模”，不管怎样忙活了一下午问题总算查出来了，这个坑分享给大家

SovietAntiInfan

这是新增的建筑：
Foundation = Custom
Foundation.X = 3
Foundation.Y = 3
Foundation.0 = 1,0
Foundation.1 = 0,1
Foundation.2 = 1,1
Foundation.3 = 2,1
Foundation.4 = 1,2
FoundationOutline.Length = 16
FoundationOutline.0 = 0,-1
FoundationOutline.1 = 1,-1
FoundationOutline.2 = 2,-1
FoundationOutline.3 = -1,0
FoundationOutline.4 = 0,0
FoundationOutline.5 = 2,0
FoundationOutline.6 = 3,0
FoundationOutline.7 = -1,1
FoundationOutline.8 = 3,1
FoundationOutline.9 = -1,2
FoundationOutline.10 = 0,2
FoundationOutline.11 = 2,2
FoundationOutline.12 = 3,2
FoundationOutline.13 = 0,3
FoundationOutline.14 = 1,3
FoundationOutline.15 = 2,3
这是精简的盟军船厂：
Foundation = Custom
Foundation.X = 4
Foundation.Y = 4
Foundation.0 = 2,0
Foundation.1 = 0,1
Foundation.2 = 1,1
Foundation.3 = 2,1
Foundation.4 = 1,2
Foundation.5 = 2,2
Foundation.6 = 3,2
Foundation.7 = 1,3
FoundationOutline.Length = 20
FoundationOutline.0 = 1,-1
FoundationOutline.1 = 2,-1
FoundationOutline.2 = 3,-1
FoundationOutline.3 = -1,0
FoundationOutline.4 = 0,0
FoundationOutline.5 = 1,0
FoundationOutline.6 = 3,0
FoundationOutline.7 = -1,1
FoundationOutline.8 = 3,1
FoundationOutline.9 = 4,1
FoundationOutline.10 = -1,2
FoundationOutline.11 = 0,2
FoundationOutline.12 = 4,2
FoundationOutline.13 = 0,3
FoundationOutline.14 = 2,3
FoundationOutline.15 = 3,3
FoundationOutline.16 = 4,3
FoundationOutline.17 = 0,4
FoundationOutline.18 = 1,4
FoundationOutline.19 = 2,4

紫色放逐

第一个格子（左上角）不能抠掉，否则ai会认为这个建筑不存在，导致一直反复建造。

SovietAntiInfan

多谢大佬指点，又试了试果然是这样，所谓第一个格子就是ares那个工具页面的（0，0）坐标，更直观的说是最上面那个角（我不太懂这个坐标方位，刚才直接试了“左边“那个角发现不行，换上边那个角就好了）